Category: MakerBot

I’ve already started work on my prinstruder as designed by Zaggo.  I’ve printed up the Idler Bracket v3 and am now printing the Motor Bracket v3.  I think the printstruder assembly is probably better suited to an earlier version of the MakerBot – one that used a “small” and “large” dino.  My batch #9 bot uses two dinos – the “Big Dino” and the “Wierd Dino.”

However, I’d really like to have an extra plastruder/printstruder on hand … just in case.

I’m several iterations into my Y axis tensioner.  I think this newest version is a pretty good improvement.  I’m now on version 7 – and have put each part in its own file.  Here’s some information about the revisions:

• The first printable version, #5 still used a single captive nut and bolt system.  The nut had to be a certain minimum distance from the center of the pulley axle in order to allow the pulley to turn freely.  However, this minimum distance also meant that the edge of the captive nut was too close to the edge of the stage – which wouldn’t allow the piece to be tightened.
• Thus, I revised the piece so that it uses two captive nut/bolt parts – one on each side of the pulley.  This allows me to set the captive nut back far enough that it leave room for the piece to be tightened without running into the pulley.
• I discovered that I had forgotten to measure one of the pieces of wood properly and ended up with a 3mm gap for the edge of the Y stage, rather than a 5mm gap.

I’ve printed up version 7, but haven’t had occasion to disassemble the Y stage yet.  The next time I do I’m installing this tensioner.  Time to design the X stage tensioner!

Some of my current MakerBot related projects:

• Trying to improve build quality.   I’m trying to tune up the hardware before I start to fiddle with Skeinforge in earnest.  I’d also like to replace one or more of my threaded rods as at least one has a warp significant enough to affect build quality.
• Printable axis tensioners.  I want to design a set of tensioners for all three axes.  Right now I’ve got a draft for the Y axis that needs to be revised.
• Printstruder.  I’ve finished the idler bracket, but still need to print all the rest of the parts.
• Chess set.  Since I’ve got WAY more black ABS then the natural (off-white) color, I want to finish dialing in the print quality on the black ABS before I start print up the white pieces.
• Chess/game board.  I’d like to design a modular board for printing out of ABS.  I’m thinking I would need three different kinds of pieces – corner, edge, and interior pieces.  I’m thinking of a connector system somewhere in-between a puzzle piece and laminate flooring, if that makes any sense at all.  Plus, being modular, you could store the pieces and board in a small box/bag.

Default Series Title

While trying to improve print quality by increasing belt tension on the X and Y axes, I did some routine maintenance.  I oiled the rods and tightened screws.  While I was at it, I took a look at my insulator retainer.  It had developed more two and a half cracks.  It had actually cracked all the way through one of the screw holes.  It was still working, but I’d rather not chance it failing while I’m printing.

So, I replaced it with one of my printed insulator retainers.  I gotta say, it feels really great to swap out a stock part for a part I built on my own ‘bot.  I suppose this is more of a repair than an upgrade… but I still choose to think of it as an upgrade.  :)

Obviously, this is an iterative process.  I revised my drawings of the axis tensioner for the Y axis a few times before trying to print it.  When I created the screenshot for it I noticed that some of the notches didn’t line up properly.  In any case, the part that fits around the pulley’s axle came out well while the part that fits on the Y stage edge didn’t come out very well, was fragile, and snapped when I was cleaning it up.  I’ll edit the file to thicken the wall of the Y axis edge piece and try it again.

Tightening the Y axis pulley is pain since you basically have to pull the entire Y stage off the X axis rods.  I suppose this isn’t a bad thing since it forces me to tighten down bolts and oil the various rods.

I designed this Axis Tensioner for the Y Axis last night.  Both parts are included in the STL file.  I’ve included the Google Sketchup file for anyone who wants to help improve the part.  It may be a little disorienting as one of the parts is laid on it’s side to be printable.

• The larger part fits around the edge of the Y axis stage.
• The smaller part fits under the Y axis pulley, around the M6 nut.
• Drop an M3 nut into the slot in the smaller part.
• Insert an M3 x 16 bolt (preferably with a washer) through the slot in the larger part.  Rotate to tighten/loosen.

Here’s the Axis Tensioner Y on Thingiverse.  Thanks to unrepentantgeek for his Sketchup version of the Cupcake CNC which allowed me to create the screenshot.

Let me know how this works for you.

I had previously noticed that the Google Sketchup STL import plugins were very hit or miss.  They probably only imported fully about 60% of the time – with more failures on complex models.  I’ve just discovered a little trick that helps tremendously.

When you are importing, you are given a several different measurement options.  I have been choosing millimeter by default.  But, if that fails to import the entire model, try again using a different measurement!  I just imported a hugely complex model by trying millimeters, centimeters, and finally meters.

Sometimes after I finish a print I know I’m going to print something else in a few minutes.  In those cases I want to keep the heater warm rather than waiting to cool it down, warm it back up, and then start printing.  Here’s my new idea – I use the in between print time to print something quick, simple, useful, and relatively worry-free.

Insulator retainer rings.  I’m guessing you just can’t have too many of these.  As suggested by Cathal Garvey, this should be a high priority print.

InnovationByLayers has done it again.  As soon as I saw he had uploaded a dalek STL, I downloaded, skeinforged it, and started printing.  1 hour and 28 minutes with a 50% infill:

Obviously you can’t print it with the arms and eye stalk as part of the body due to overhang issues.  However, I wrapped the unsharp end of my smallest drill bit (1/16″) in a thick rubber band to give it grip and drilled three holes for the arms and eye stalk.  I then used pieces of discarded filament that had been stretched as I backed it out of the extruder for the arms and eye stalk.  I wrapped the arms/eye stalk in small pieces of black electrical tape to finish the look.  Here’s what it looked like before I augmented it:

In fact, I was so pleased with this build that I printed up a second with a 0% infill.  FYI, that took 52 minutes and apparently had no affect on the final product.  Although, it does sound hollow.