DrawBot – Printed Parts

So far I’ve got three types of printed parts:

  1. Spools
    1. These spools hold the monofilament and are friction fit onto the motor shaft.  You can check out the designs on Thingiverse.
  2. Motor Mounts
    1. The Thingiverse page actually has a lot of information about the motor mounts.  They’re designed in OpenSCAD and are mostly parametric.  Since I’m mounting these motors inside a box, the mounts are designed to go into the corners of the box.
  3. John Abella’s Gondola
    1. I haven’t hooked everything up yet, so I don’t know how well this will work.  I can’t wait to find out!
  4. Arduino Mount
    1. I’m kicking around some ideas for how this would work.  Ideally, I’ll end up designing a bracket that the Arduino and motor shield can just snap into.
Posts in the DrawBot Adventure Series
  1. Wanna make a DrawBot?
  2. DrawBot Resources and Links
  3. DrawBot, the Adventure Begins
  4. DrawBots for the slow learner
  5. DrawBot - Parts Ordered!!!
  6. DrawBot - The Breakdown
  7. DrawBot - Parts Shipped!!!
  8. DrawBot - What would you draw?
  9. DrawBot - The Plan!
  10. DrawBot - The Hacks
  11. DrawBot - The Delivery?
  12. DrawBot - The Delivery, Part II
  13. DrawBot – The Delivery, Part III
  14. DrawBot – The Assembly, Part I
  15. DrawBot – The Software, Part I (and an existential conversation)
  16. DrawBot – The Delivery, Part IV
  17. DrawBot – The Assembly, Part II
  18. DrawBot – The Assembly, Part III
  19. DrawBot – The Assembly, Part IV
  20. DrawBot – Halp!!! No - seriously, a little help?
  21. DrawBot – The Delivery, Part V
  22. DrawBot – The Silver Lining of Failure
  23. DrawBot – The Delivery, Part VI
  24. DrawBot – The Assembly, Part V
  25. DrawBot – The Assembly, Part VI
  26. DrawBot – Printed Parts
  27. DrawBot – The Assembly, Part VII
  28. DrawBot – The Operation, Part I
  29. DrawBot – The Breakdown, Part II
  30. DrawBot – Printing!
  31. DrawBot – Printing, Part II
  32. DrawBot – Why are you crying?
  33. DrawBot – Calibration
  34. DrawBot – Pen Selection
  35. DrawBot – How to Recover from a Stalled Print!
  36. DrawBot – Drawing Success(ish)!!!
  37. DrawBot – Pen Selection, Part II
  38. DrawBot – Onwards and Upwards!
  39. DrawBot – Another Successful(ish) Drawing!, and an Update
  40. Restarting a Stalled DrawBot Drawing
  41. TSP FTW!
  42. Speedier DrawBot Drawings
  43. Two new DrawBot links! And an update!
  44. Excellent DrawBot Slides
  45. Another Drawing Robot!!!
  46. DrawBot Practice Tip: A Watched Pot
  47. The biggest inkjet printer ever
  48. Why do DrawBots draw on walls?
  49. Maze Code + Polargraph?
  50. Ideas for improving my DrawBot
  51. DrawBot Aesthetic Re-Design Ideas
  52. The Eagle Has Landed
  53. Every Body Needs a Skull
  54. This project is not going to overengineer itself
  55. Overengineered Spools
  56. Overengineered Bolt Endcaps, Case Holder
  57. Sourcing DrawBot Parts
  58. DrawBot - A Tour!
  59. DrawBot - A Preview
  60. Arduino Powered Drawing Robot Poll
  61. Building an Arduino Drawing Robot - On The Cheap
  62. DrawBot - Printed Parts Tour
  63. Unidentified Foam Object
  64. Arduino Powered Drawing Robot - Take 2 (Or 3)
  65. DrawBot, now ACTUALLY wall mounted!
  66. A Study of Drawing Robot Pen Holders and Design Considerations
  67. Drawing Robot Pen Holders, Calligraphy Pens, and Thought Experiments
  68. Ideal Qualities in a Drawing Robot Pen Holder
  69. Enough talk! Finally a pen holder!
  70. DrawBot Pen Holder Post Mortem
  71. To Maker Faire!!!
  72. Skipping! How could I forget the skipping?!
  73. PlotterBot at Maker Faire Bay Area 2013!
  74. PlotterBot.com - a new site dedicated to drawing robots

Leave a Reply

Your email address will not be published. Required fields are marked *